QHYCCD

Recent Posts

Pages: 1 2 [3] 4 5 ... 10
21
Image Issue Q&A / Re: QHY268C Buffers Three Frames
« Last post by TigerClaw on May 07, 2021, 12:16:05 AM »
In EZCAP it seems to work fine. But the Temp. monitor crashed yesterday 2x after some minutes.

In APT it also works fine. But if I disconnect the camera and connect it again the exposure will be endless and I cannot change it. SO I have to restart APT.

And I have to set the Cooling Steps to "0" to get the right temperature.
22
Mechanical Q&A / Re: QHY5III178mono problems
« Last post by jwestervelt on May 06, 2021, 11:51:53 PM »
I have more information...

If I delay the load of the firmware via fxload, the device remains attached, but it shows up as Westbridge instead of the Titan178U.  When I load the firmware, it has a very high chance of disconnecting the device... so I suspect it is a problem with the camera's internal storage and the firmware is not getting transferred reliably.
23
Mechanical Q&A / Re: QHY5III178mono problems
« Last post by jwestervelt on May 06, 2021, 10:49:45 PM »
Here is the log from linux.  I repeatedly removed and reinserted the cable until it finally enumerated the device.

May  6 20:45:35 scandium kernel: usb 3-2: new high-speed USB device number 30 using xhci_hcd
May  6 20:45:35 scandium kernel: usb 3-2: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:45:35 scandium kernel: usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:45:35 scandium kernel: usb 3-2: Product: WestBridge
May  6 20:45:35 scandium kernel: usb 3-2: Manufacturer: Cypress
May  6 20:45:35 scandium kernel: usb 3-2: SerialNumber: 0000000004BE
May  6 20:45:35 scandium kernel: usb 3-2: USB disconnect, device number 30
May  6 20:45:37 scandium kernel: usb 3-2: new high-speed USB device number 31 using xhci_hcd
May  6 20:45:37 scandium kernel: usb 3-2: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:45:37 scandium kernel: usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:45:37 scandium kernel: usb 3-2: Product: WestBridge
May  6 20:45:37 scandium kernel: usb 3-2: Manufacturer: Cypress
May  6 20:45:37 scandium kernel: usb 3-2: SerialNumber: 0000000004BE
May  6 20:45:37 scandium kernel: usb 3-2: USB disconnect, device number 31
May  6 20:45:48 scandium kernel: usb 3-2: new high-speed USB device number 32 using xhci_hcd
May  6 20:45:48 scandium kernel: usb 3-2: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:45:48 scandium kernel: usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:45:48 scandium kernel: usb 3-2: Product: WestBridge
May  6 20:45:48 scandium kernel: usb 3-2: Manufacturer: Cypress
May  6 20:45:48 scandium kernel: usb 3-2: SerialNumber: 0000000004BE
May  6 20:45:49 scandium kernel: usb 3-2: USB disconnect, device number 32
May  6 20:46:06 scandium kernel: usb 3-3: new high-speed USB device number 33 using xhci_hcd
May  6 20:46:06 scandium kernel: usb 3-3: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:46:06 scandium kernel: usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:46:06 scandium kernel: usb 3-3: Product: WestBridge
May  6 20:46:06 scandium kernel: usb 3-3: Manufacturer: Cypress
May  6 20:46:06 scandium kernel: usb 3-3: SerialNumber: 0000000004BE
May  6 20:46:06 scandium kernel: usb 3-3: USB disconnect, device number 33
May  6 20:46:11 scandium kernel: usb 3-3: new high-speed USB device number 34 using xhci_hcd
May  6 20:46:11 scandium kernel: usb 3-3: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:46:11 scandium kernel: usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:46:11 scandium kernel: usb 3-3: Product: WestBridge
May  6 20:46:11 scandium kernel: usb 3-3: Manufacturer: Cypress
May  6 20:46:11 scandium kernel: usb 3-3: SerialNumber: 0000000004BE
May  6 20:46:12 scandium kernel: usb 3-3: USB disconnect, device number 34
May  6 20:46:14 scandium kernel: usb 3-3: new high-speed USB device number 35 using xhci_hcd
May  6 20:46:14 scandium kernel: usb 3-3: New USB device found, idVendor=1618, idProduct=0178, bcdDevice= 1.00
May  6 20:46:14 scandium kernel: usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  6 20:46:14 scandium kernel: usb 3-3: Product: WestBridge
May  6 20:46:14 scandium kernel: usb 3-3: Manufacturer: Cypress
May  6 20:46:14 scandium kernel: usb 3-3: SerialNumber: 0000000004BE
May  6 20:46:14 scandium kernel: usb 3-3: USB disconnect, device number 35
May  6 20:46:14 scandium kernel: usb 3-3: new high-speed USB device number 36 using xhci_hcd
May  6 20:46:15 scandium kernel: usb 3-3: New USB device found, idVendor=1618, idProduct=0179, bcdDevice= 0.00
May  6 20:46:15 scandium kernel: usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
May  6 20:46:15 scandium kernel: usb 3-3: Product: Titan178U
May  6 20:46:15 scandium kernel: usb 3-3: Manufacturer: QHYCCD
24
QHYCCD SDK FOR WINDOWS / Re: Autoexposure and QHY camera
« Last post by QinXiaoXu on May 06, 2021, 09:59:20 PM »
Hi,
    We added this function in SDK,but it isn't a thorough function,so this is not available,I'm not sure if SharpCap added this function by theyselves.
Best Regards,
QinXiaoXu
25
QHYCCD SDK for LINUX / Re: QHY462C and QHY294PROC issue on Raspberry Pi 4B
« Last post by QinXiaoXu on May 06, 2021, 09:52:54 PM »
你好,
    我稍后测试一下两个相机同时连接的问题。
26
QHYCCD SDK FOR WINDOWS / Re: QHY CFW3 firmware source code?
« Last post by QinXiaoXu on May 06, 2021, 09:48:03 PM »
Hi,
    I think we didn't try use new version Arduino,the CFW board is old version,new version has this option,so we use the old version all the time.
Best Regards,
QinXiaoXu
27
Image Issue Q&A / Re: QHY268C Buffers Three Frames
« Last post by QinXiaoXu on May 06, 2021, 09:28:35 PM »
Hi,
    EZCAP and SharpCap is used under different work mode,and now I'm modify SDK to solve the SharpCap issue.
    And you said in APT camera can't cooler normally,can it work well in EZCAP_Qt?
Best Regards,
QinXiaoXu
28
Image Issue Q&A / Re: QHY294M Pro cannot find 2nd CFW (ASCOM)
« Last post by QinXiaoXu on May 06, 2021, 09:21:32 PM »
Hi,
    We modified and solved this issue,the update will be release at next update.You can try this ahead,it contains two version,for ASCOM Platform 6.4 and 6.5,you need select occording to you installed ASCOM Platform.
Best Regards,
QinXiaoXu
29
Image Issue Q&A / Re: QHY16200A uneven illumination issue
« Last post by Yuki on May 06, 2021, 09:20:38 PM »
I think it is overscan area, you can select it in the ASCOM setup.

Best Regards
30
Hi,
    The "Switch on" you said,if it mean power on?Now after power on camera's FPGA and firmware will setup target temperature to be 0.
Best Regards,
QinXiaoXu
Pages: 1 2 [3] 4 5 ... 10